Mechanical climber model DT300


Mechanical climber DT300
General information about mechanical climber:
Mechanical climber is designed with manual control system and observing all safety points.
This climber can be used for painting, painting, cleaning various surfaces in a fixed and moving way.
This climber is installed on special places with steel tow wire with a diameter of 8 mm.
This device can be easily and quickly assembled and can be used at different heights.
The climber can withstand a weight of 350 kg.

Climber as the best alternative to metal scaffolding (facade scaffolding) has the following advantages:
High economic justification and reduction of financial costs
High security for users
Increase user performance speed and high efficiency
Accelerate installation and assembly
Low volume and reduced space around the building

Mechanical information of mechanical climber:
Climber has a high strength and according to the type of light metal used in its construction, it can be used at different heights and under different pressures.
Two tow ropes are placed on the climbers, one of which is a tow wire for carriers.
The other two tow ropes are used as safety tow ropes.
Due to the presence of the brake system in this device, it can be used at any height.
The braking system is V-shaped, which increases with increasing weight.
The system is centrifugal brake (parachute).
The gears of this device are made of 8620 cemented steel and its strength in heat has increased.

 

Net weight of the deviceKg  11
The weight bearing capacity of each climberKg 350
Cable diameter usedMM  8
Moving the lift rack for one turn of the handleCM 5/7
Tolerable ambient temperature20- up to +60 degrees Celsius
Load test %  25+
Cable weight per unit lengthKg/M 22/0

 

How to use the above mechanical:
When assembling the clipper, two red and yellow keys should always be on the left and top of the user.
Attach the winches to the basket from the bottom with two screws and nuts of 60 x 60.
When the assembly is complete, run the towbar through the gray hole on the machine.
Push the right hand lever clockwise by pushing the tow wire into the winch.
Keep doing this until the end of the tow wire comes out of the winch outlet hole and becomes firm.
After tightening the basket wire carrying the basket, pass the safety tow wire through the red hole and pull it from the bottom until the empty space is filled and the tow wire is tightened by hand.
Attach a weight of 15 to 20 kg to the end of the safety tow wire so that it is slightly away from the ground.
After performing all the above steps, the clipper is ready to use.

Basket of climbers

The baskets produced for the climber are designed and made according to the type of use and equipment required.

Mechanical climber basket:
There are baskets designed and built for mechanical climbers.
Depending on the type of use in different conditions, it is designed and manufactured in different sizes.
In mechanical climbers, for easy and safer use at any height, security systems and suitable packages have been used.
In mechanical baskets, the place where the tow wires are installed is designed and made in such a way that it does not impede the movement of the basket.
کلایمر

 

Climber basket with single use:
Used for exterior painting and cleaning in places that do not have enough space.
In large buildings, it is installed in special places and rain-proof areas.
Designed and built to clean indoor areas such as heating appliances and places where one-on-one operations are required.

کلایمر

How to install climbers on buildings and industrial structures
In this method, special structures with climber balance weights are used on the building.
Roof structures contain a counter counter weight basket, or arm attached to the hinges and support of the climber balance.
A weight of 300 kg is used to create balance on the device.
Due to the installation of special wheels on the balance weight basket, the device can be easily moved in different directions without removing the weights and other equipment.
Use the clip on the turret:
In buildings with retaining walls, the basket is used with these special climber clamps without the slightest damage to the building.
Clamps on the ramp are designed and built according to the type of wall of buildings.

Towing wire:
Special tow ropes have been used for mechanical and electrical climbers.
The tow ropes are cut in different sizes and to maintain the safety of the tip of the cut part, it is pressed with lead and fixed with special clamps. comes.

How to lift the basket with a mechanical clipper:
Turn the handle of the right mechanical winch and place it on the red dot on the body.
Turn the mechanical winch to the left by turning the knob to the left clockwise.
Turn both knobs clockwise.
Continue the process of raising the basket to the desired height.
Stop rotating the handles when you reach the desired height.
In this case, the braking system will keep the whole mechanical climber constant.

How to lower the basket with a mechanical clipper:
Release the left handle to lower the basket. You will see that the left handle is released.
Use your finger to bring up the red key on the left side of the mechanical towing wire and hold it in the same position.
Turn the left knob counterclockwise to reach the desired height.
When you reach the desired height, stop turning the knob and release the red mechanical climber key.
Security systems used in mechanical climbers:
Centrifugal or parachute braking system:

This braking system acts when the mechanical climber accelerates and prevents the device from falling.

This system is also used in elevators under the name of parachute as a security system.

Lining brake system with lining plates:

This system acts like a car brake and prevents the device from accelerating and falling.

It can be used to hold a mechanical climber at any height.

Reliability increase system with increasing load:

No matter how much the load of the climber or the so-called weight of the user basket is added, this mechanism intensifies the self-braking mode in the climber.

This mechanism locks the climber to prevent various hazards.

Safety brake system and safety tow wire:

An independent security system called security tow wire is also located on the climber.

This towline operates completely independently and in the event that none of the various security components mentioned above come into operation, it causes the entire climber assembly to be locked on this towline to prevent the climber from falling.

Essentials that must be observed when using the climber device
In order to install and use the device, an 8 mm diameter steel wire tow wire must be used for the carrier and security part.
Each lift has a displacement capacity of 350 kg.
When in the basket of the device, use security devices such as seat belts, helmets, personal safety belts, etc.
Do not carry cargo outside the climber and do not use this device as an elevator.
Repair and maintenance of equipment is performed periodically according to the standards and information provided by the introduced service.
Climber basket is used assembled.
Avoid doing this without attaching a 15 to 20 kg weight to the tip of the safety tow wire.
Avoid lubricating the surface of the tow ropes.

بدون نظر

Leave a Reply

Your email address will not be published. Required fields are marked *